Home > Wooden Speakers > Teach you how to adapt the power amplifier and audio from the technical aspect

Teach you how to adapt the power amplifier and audio from the technical aspect

2021-07-06 347
The matching of power amplifier and speakers pays attention to suitable heating and cooling, moderate soft and hard, in order to realize the neutral tone of the whole set of equipment, which is only considered from the artistic point of view. However, the technical considerations are:

1. Power matching

2. Power reserve matching

Three, impedance matching

Fourth, the matching of damping coefficient

If we recognize the above four points when mating, the performance of the equipment used can be maximized and fully displayed.


Power matching

In order to meet the requirements of high-fidelity listening, the rated power should be determined according to the best listening sound pressure. We all feel this way:

1. The volume is small, the sound is weak, thin, dynamic, dull, low frequency is significantly lacking, and fullness is poor, and the sound seems to be shrinking inside and unable to come out.

2. When the volume is right, the sound is natural, clear, round, soft, full, powerful, and dynamic.

3. But when the volume is too loud, the sound will be blunt, not soft, rough, and have an ear-piercing feeling.


Teach you how to adapt the power amplifier and audio from the technical aspect


Therefore, the replay sound pressure level has a greater relationship with the sound quality. The sound pressure level in the listening area is preferably 80~85dB (A-weighted), which can be calculated from the distance from the listening area to the speaker and the characteristic sensitivity of the speaker The rated power of the speaker and the rated power of the amplifier.

Power reserve matching

Loudspeaker: In order to enable it to withstand the impact of strong bursts in the program signal without being damaged or distorted. Here is an empirical value for reference: the nominal rated power of the selected speaker should be three times the theoretically calculated power.

Power amplifier: Compared with a transistor power amplifier, a tube power amplifier requires a different power reserve. This is because the overload curve of the tube amplifier is relatively flat. For the peak of the over-loaded music signal, the tube power amplifier does not obviously produce clipping, but only rounds the tip of the peak. This is what we often call flexible shear peaks. After the transistor power is placed at the overload point, the non-linear distortion increases rapidly, causing serious clipping of the signal. It does not round the peak but cuts it neatly. Someone used a composite impedance composed of resistance, inductance, and capacitance to simulate speakers, and tested the actual output capabilities of several high-quality transistor power amplifiers. The results show that when the load has a phase shift, there is a nominal 100W power amplifier, and the actual output power is only 5W when the distortion is 1%!

Therefore, the selection of the reserve amount of the transistor power amplifier:

High fidelity power amplifier: 10 times

High-end civil power amplifier: 6 to 7 times

Civil mid-range power amplifier: 3 to 4 times,

The tube power amplifier can be much smaller than the above ratio.

How much margin should be left for the average sound pressure level and maximum sound pressure level of the system depends on the content of the program and the working environment. This redundancy is at least 10dB,

For modern pop music, bungee music and other music, you need to leave a 20~25dB redundancy, so that the sound system can work safely and stably.

Impedance matching

It refers to the rated output impedance of the power amplifier, which should be consistent with the rated impedance of the speaker. At this time, the power amplifier is in the best designed load line state, so the maximum undistorted power can be given.

If the rated impedance of the speaker is greater than the rated output impedance of the power amplifier, the actual output power of the power amplifier will be less than the rated output power.

If the rated impedance of the speaker is less than the rated output impedance of the power amplifier, the audio system can work, but the power amplifier is in danger of overload. The power amplifier is required to have complete overcurrent protection measures to solve it. The impedance matching requirements for the tube power amplifier are more stringent.

Matching of damping coefficient

The damping coefficient KD is defined as: KD = rated output impedance of the power amplifier (equal to the rated impedance of the speaker) / internal resistance of the power amplifier output

Since the internal resistance of the power amplifier output has actually become the resistance of the speaker, the KD value determines the amount of resistance experienced by the speaker. The larger the KD value is, the heavier the resistance is. Of course, the KD value of the power amplifier is not the better. Too much KD will make the speaker resistance too heavy, so that the pulse front settling time will increase and the transient response index will be reduced. Therefore, one-sided pursuit of a large KD value should not be one-sided when choosing a power amplifier.

As a household high-fidelity power amplifier damping coefficient, there is an empirical value for reference. The minimum requirement: the KD value of transistor power amplifier is greater than or equal to 40, and the KD value of tube power amplifier is greater than or equal to 6.

The basic conditions to ensure good sound performance in the steady state and transient state, attention should be paid to the coordination of the equivalent mechanical quality factor (Qm) of the speaker and the damping coefficient (KD) of the amplifier. This coordination requires the speaker's feeder to be used as the overall sound system Part of it to consider. The equivalent resistance of the feeder of the speaker should be small enough to be negligible compared with the rated impedance of the speaker. In fact, the power loss of the speaker feeder should be less than 0.5dB (about 12%) to achieve this coordination.
Wooden Speakers:https://www.zeshuiplatform.com/
Like to share
If you like our information, please share to your friends know.
Tags: Wooden Speakers

0

Links:
Website building SEO absorbing material USB Microphone CN ZeShui Passive Speaker Bluetooth Speaker Usb fan Ketone Breath Meter
Service:
Amazon Shopee USB Microphone Computer Microphone Wooden Speakers Wooden Headphones Absorbing Material Shielding Material
Shenzhen ZeShui Trading Co., Ltd. All rights reserved ©2021